How To Set A Rainbird 5000 Sprinkler

Provided past Rainbird.com

Rainbird is one of the most reliable underground sprinkler organisation brands there is. Their products are reliable and easy to adjust. Notwithstanding, I am going to share some pro tips you may not know that will brand adjusting the Rainbird 5000 Sprinkler Heads a breeze.

Disclosure: All links contained in this article are affiliate links. This means if you found value in what was covered in this article or this site you can help support what I am doing past purchasing your materials with the links contained below. By doing so, I will receive a small commission based on your purchases. Thank you!

Special Note:

If your sprinkler head is not turning or rotating adjusting it will not assistance. Unfortunately, the but affair yous tin do to ready it is to supervene upon the entire sprinkler caput. After adjusting the head it may rotate for a wheel or two, simply it will inevitably stop rotating in the same place.

Required Tools:

I hate reading through an entire mail just to find you demand special tools to complete the job, so I volition lay them out for you lot in the beginning. Luckily you only need 2 tools and can get away with only have one of them.

Channellock Pliers

Channellock 440 12-Inch Tongue and Groove Plier

These are used to grab the sprinkler head at the base and rotate it into position. Sometimes you tin rotate the caput by the cervix, but I practise non recommend it.

Adjustment Key or a Flat Head Screwdriver

A Rainbird Adjustment fundamental is not 100% necessary when adjusting a Rainbird 5000 Sprinkler Head, if you do not have one, you tin can use the Flat Caput Screwdriver. Having the fundamental makes it easy to pull the Rainbird 5000 Sprinkler Head out from its case, or up out of the ground.

Lets Start!

1. Begin adjusting past locating the Left Stop or hard Cease setting of the Rainbird 5000 Sprinkler Head.

   • Rotate the top of the sprinkler head (turret) all the mode to the Correct and then back to the left.
   • When the turret of the sprinkler heads stops on the left side, this is known as the hard finish.
   • No matter what y'all do with the key, the caput will e'er stop in the same place on the left side.

2. Left Stop Adjustment Or Difficult Terminate on Your Rainbird 5000 Sprinkler Caput.

   • To practice this y'all will need to physically turn the unabridged head to align it where you want the left side to spray.
   • Using a pair of Channellock Pliers, rotate the unabridged head to the correct, and marshal the head where yous desire the left side to stop.
     • Why turn information technology to the correct? If you turn it to the left, it could mayhap unthread the sprinkler head from the plumbing fixtures, making a HUGE MESS.
     • If you find it is too hard to turn to the correct, and then go on to turn the caput to the left.

3. Adjust the Right Terminate of the Rainbird 5000 Sprinkler Head.

   • Once the left side is set y'all can at present, ready the correct stop, this is done with the key or a flat caput screwdriver.

     

     Provided past Rainbird.com

   • Rotate the turret all the fashion to the right side and every bit yous plough it back towards the left side, stop turning it where you want the right side to cease
   • Next, insert the key or a flat head screwdriver and turn it counterclockwise while holding the turret
     • Rotate the turret over to the left stop and back to the right to verify the adjustment.
     • If you lot went also far, turn the key clockwise to increment the radius.

4. Adapt the Spray Blueprint.

   • In one case the rotation is set, now yous can decrease the spray design.
   • Insert the flat head screwdriver directly over the nozzle location until it engages a flat caput screw.

     

     Provided by Rainbird.com

     • Annotation:Sometimes this is kind of hard to get locked in, particularly if it has been overgrown with dirt and grass. Experience free to skin dorsum the rubber dust cover to encounter how the key needs to be aligned.
   • Rotate the nozzle adjustment screw clockwise to subtract the spray design and counterclockwise to increase. DO NOT Plow It TOO FAR TO THE LEFT. This will cause the aligning spiral to back out and you lot will NEVER detect it.

5. Verify the Aligning.

   • Rotate the head through its full range of motion and ensure information technology is starting and stopping correctly
   • Next, rotate the caput about all the way to the left side and allow the Railbird 5000 Sprinkler Head to finish the rotation on its one. Notation: sometimes the heads will rotate differently on their own, sometimes more and sometimes less.
   • Echo Step ii or iii as necessary.

Please comment below or send me an email with your feedback here. Also, If you found something of value delight like and share this post, Thank Yous!

Source: https://sprinklerresource.com/adjustingrainbird5000/

Share this post